For full functionality of this site it is necessary to enable JavaScript.

Fluke 726 多功能过程校准器

 

Measurement Accuracy

Voltage DC

30.000 V

0.01%+ 2 mV (upper display)

20.000 V

0.01%+ 2 mV (lower display)

90.00 mV

0.01%+ 10µV

-10.00 mV to 75.00 mV

0.025 % + 1 count (via TC connector)

Current DC

24.000 mA

0.01%+ 2 mA

Resistance

0.0 to 4000.0 Ω

+/- 0.015%

Frequency

2.0 to 1000.0 CPM

0.05 % + 0.1 cpm

1.0 to 1000.0 Hz

0.05 % + 0.1 Hz

1.00 to 15.00 kHz

0.05 % + 0.01 kHz

Sensitivity

1 V peak-to-peak-minimum

Pressure

Accuracy

from 0.025% of range using any of 29 pressure modules.(for detailed specifications refer to pressure modules in options and accessories)
Modules available for differential, gauge, vacuum, absolute, dual and high pressure.

Source Accuracy

 

Voltage DC

100.00 mV

0.01%+10 µV

20.000 V

0.01%+2 mV

-10.00 mV to 75.00 mV

0.025 % + 1 count (via TC connector)

Current DC

24.000 mA (Source)

0.01%+ 2 µA

24.000 mA (Simulate)

0.01%+ 2 µA

Resistance

Range, Accuracy (Percent of reading + floor) and Excitation Current

5 to 400 Ω, 0.015% + 0.1 Ω, 0.1 to 0.5mA
5 to 400 Ω, 0.015% + 0.05 Ω, 0.5 to 3mA
400 to 1500 Ω, 0.015% + 0.5 Ω, 0.05 to 0.8 mA
1500 to 4000 Ω, 0.015% + 0.5 Ω, 0.05 to 0.4 mA

Frequency

2.0 to 1000.0 CPM

0.05%

1.0 to 1000.0 Hz

0.05%

1.0 to 10.0 kHz

0.25%

10.0 to 15.0 kHz

0.5%

Waveform:

5 V p-p squarewave, -0.1 V offset

RTDs and Thermocouples

Measure and Source Accuracy:

Cu10
NI-120
PT-100 (385)
PT-100 (392)
PT-100 (391-JIS)
PT-200 (385)
PT-500 (385)
PT-1000 (385)
RTD Resolution:
Cu10.01 C
J:
K:
T:
E:
R:
S:
B:
L:
U:
N:
XK:
BP:
TC Resolution

1.8 °C
0.15 °C
0.45 °C
0.35 °C
0.35 °C
0.95 °C
0.55 °C
0.35 °C
0.01 C (0.01 F) 
0.1 C (0.1 F)
0.4 °C
0.5 °C
0.4 °C
0.4 °C
1.4 °C
1.4 °C
1.4 °C
0.45 °C
0.45 °C
0.6 °C
0.4 °C
1.1 °C
J, K, T, E, L, N, U: 0.1 °C, 0.1 °F B, R, S: 1 °C, 1 °F

Specifications

Ramp Functions

Source functions:

Voltage, current, resistance, frequency, temperature

Ramps

Slow ramp, Fast ramp, 25% step-ramp

Loop Power Function

Voltage:

24 V

Accuracy:

10%

Maximum current:

22 mA, short circuit protected

Step Functions

Source functions:

Voltage, current, resistance, frequency, temperature

Steps

25% of range, 100% of range

Environmental Specifications

Operating Temperature

-10 °C to +55 °C

Storage Temperature

-20 °C to 71 °C

Operating Altitude

3000 m

Safety Specifications

Agency Approvals

EN 61010-1:1993, ANSI/ISA S82.01-1994; CAN/CSA C22.2 No 1010.1:1992

Mechanical & General Specifications

Size

200mm x 96mm x 47mm (7.9 in x 3.8 in x 1.9 in)

Weight

650 g (23 oz.)

Batteries

4 AA alkaline batteries

Battery Replacement

Separate battery compartment, accessable without breaking calibration seal

Side port connections

Pressure module connector, also used for remote real-time programming

 

 

 

 

 

Details
  Description

 

Get More Calibration Power

The Fluke 726 Precision Multifunction Process Calibrator is designed specifically for the Process industry with broad workload coverage, calibration power and unsurpassed accuracy in mind. The 726 measures and sources almost all process parameters and can calibrate almost anything. The 726 will also interpret results without the help of a calculator and store measurement data for later analysis.

Features
  • More precise measurement and calibration source performance, accuracies of 0.01%.
  • Two separate channels; measure, source and view process signals simultaneously
  • Measure volts, mA, RTDs, thermocouples, frequency, and resistance to test sensors and transmitters
  • Source/simulate volts, mA, thermocouples , RTDs, frequency, ohms, and pressure to calibrate transmitters
  • Measure/source pressure using any of 29 Fluke 700Pxx Pressure Modules
  • Source mA with simultaneous pressure measurement to conduct valve and I/P tests
  • Integrated pressure switch test allows you to capture the set, reset and deadband of a switch
  • Memory storage for up to 8 calibration results, return stored calibration data from the field for later analysis
  • Transmitter error% calculation, interpret calibration results without a calculator
  • Perform fast linearity tests with auto step and auto ramp features
  • Power transmitters during test using 24 V loop supply and simultaneous mA measurement
  • Store frequently-used test setups for later use
  • Frequency totalizer and frequency pulse train source mode for enhanced flowmeter testing
  • HART mode inserts 250 ohm resistor in mA measure and source for compatibility with HART instrumentation
  • Custom RTD curves, add calibration constants for certified RTD probes for enhanced temperature measurement
  • New voltage input protection design for improved reliability
  • Three-year warranty

Includes

  • One set of AC72 alligator clips
  • One set of stackable test leads
  • One set of TL 75 testleads
  • User manuals
  • NIST- traceable calibration report and data

 

  • 质量承诺
  • 正品保修
  • 送货到家
  • 交易简单化

注册收新闻 - 获得优惠活动的机会